Sound Pressure Level

Sound pressure or acoustic pressure is the local pressure deviation from the ambient (average or equilibrium) atmospheric pressure, caused by a sound wave. In air, sound pressure can be measured using a microphone, and in water with a hydrophone. The SI unit of sound pressure is the pascal (Pa).

Mathematical definition

A sound wave in a transmission medium causes a deviation (sound pressure, a ''dynamic'' pressure) in the local ambient pressure, a ''static'' pressure.

Sound pressure, denoted ''p'', is defined by
$p_\text = p_\text + p,$
where
* ''p''_total is the total pressure,
* ''p''_stat is the static pressure.

Sound measurements

Sound intensity

In a sound wave, the complementary variable to sound pressure is the particle velocity. Together, they determine the sound intensity of the wave.

''Sound intensity'', denoted I and measured in W· m⁻² in SI units, is defined by
$\mathbf I = p \mathbf v,$
where
* ''p'' is the sound pressure,
* v is the particle velocity.

Acoustic impedance

''Acoustic impedance'', denoted ''Z'' and measured in Pa·m⁻³·s in SI units, is defined by
$Z(s) = \frac,$
where
* $\hat(s)$ is the Laplace transform of sound pressure,
* $\hat(s)$ is the Laplace transform of sound volume flow rate.

''Specific acoustic impedance'', denoted ''z'' and measured in Pa·m⁻¹·s in SI units, is defined by
$z(s) = \frac,$
where
* $\hat(s)$ is the Laplace transform of sound pressure,
* $\hat(s)$ is the Laplace transform of particle velocity.

Particle displacement

The ''particle displacement'' of a ''progressive sine wave'' is given by
$\delta(\mathbf, t) = \delta_\text \cos(\mathbf \cdot \mathbf - \omega t + \varphi_),$
where
* $\delta_\text$ is the amplitude of the particle displacement,
* $\varphi_$ is the phase shift of the particle displacement,
* k is the angular wavevector,
* ''ω'' is the angular frequency.

It follows that the particle velocity and the sound pressure along the direction of propagation of the sound wave ''x'' are given by
$v(\mathbf, t) = \frac (\mathbf, t) = \omega \delta_\text \cos\left(\mathbf \cdot \mathbf - \omega t + \varphi_ + \frac\right) = v_\text \cos(\mathbf \cdot \mathbf - \omega t + \varphi_),$
$p(\mathbf, t) = -\rho c^2 \frac (\mathbf, t) = \rho c^2 k_x \delta_\text \cos\left(\mathbf \cdot \mathbf - \omega t + \varphi_ + \frac\right) = p_\text \cos(\mathbf \cdot \mathbf - \omega t + \varphi_),$
where
* ''v''_m is the amplitude of the particle velocity,
* $\varphi_$ is the phase shift of the particle velocity,
* ''p''_m is the amplitude of the acoustic pressure,
* $\varphi_$ is the phase shift of the acoustic pressure.

Taking the Laplace transforms of ''v'' and ''p'' with respect to time yields
$\hat(\mathbf, s) = v_\text \frac,$
$\hat(\mathbf, s) = p_\text \frac.$

Since $\varphi_ = \varphi_$, the amplitude of the specific acoustic impedance is given by
$z_\text(\mathbf, s) = , z(\mathbf, s), = \left, \frac\ = \frac = \frac.$

Consequently, the amplitude of the particle displacement is related to that of the acoustic velocity and the sound pressure by
$\delta_\text = \frac,$
$\delta_\text = \frac.$

Inverse-proportional law

When measuring the sound pressure created by a sound source, it is important to measure the distance from the object as well, since the sound pressure of a ''spherical'' sound wave decreases as 1/''r'' from the centre of the sphere (and not as 1/''r''², like the sound intensity):
$p(r) \propto \frac.$

This relationship is an ''inverse-proportional law''.

If the sound pressure ''p''₁ is measured at a distance ''r''₁ from the centre of the sphere, the sound pressure ''p''₂ at another position ''r''₂ can be calculated:
$p_2 = \frac\,p_1.$

The inverse-proportional law for sound pressure comes from the inverse-square law for sound intensity:
$I(r) \propto \frac.$
Indeed,
I(r) = p(r) v(r) = p(r)\left * z^\rightr) \propto p^2(r),
where
* $*$ is the convolution operator,
* ''z''⁻¹ is the convolution inverse of the specific acoustic impedance,
hence the inverse-proportional law:
$p(r) \propto \frac.$

The sound pressure may vary in direction from the centre of the sphere as well, so measurements at different angles may be necessary, depending on the situation. An obvious example of a sound source whose spherical sound wave varies in level in different directions is a bullhorn.

Sound pressure level

Sound pressure level (SPL) or acoustic pressure level is a logarithmic measure of the effective pressure of a sound relative to a reference value.

Sound pressure level, denoted ''L''_''p'' and measured in dB,"Letter symbols to be used in electrical technology – Part 3: Logarithmic and related quantities, and their units"
''IEC 60027-3 Ed. 3.0'', International Electrotechnical Commission, 19 July 2002. is defined by:
$L_p = \ln\left(\frac\right) ~ \text = 2 \log_\left(\frac\right)~\text = 20 \log_\left(\frac\right)~\text,$
where
* ''p'' is the root mean square sound pressure,
* ''p''₀ is a reference sound pressure,
* is the neper,
* is the bel,
* is the decibel.

The commonly used reference sound pressure in air is

which is often considered as the threshold of human hearing (roughly the sound of a mosquito flying 3 m away). The proper notations for sound pressure level using this reference are or , but the suffix notations , , dBSPL, or dB_SPL are very common, even if they are not accepted by the SI.Thompson, A. and Taylor, B. N. Sec. 8.7: "Logarithmic quantities and units: level, neper, bel", ''Guide for the Use of the International System of Units (SI) 2008 Edition'', NIST Special Publication 811, 2nd printing (November 2008), SP81
PDF

Most sound-level measurements will be made relative to this reference, meaning will equal an SPL of . In other media, such as underwater, a reference level of is used. These references are defined in ANSI S1.1-2013.

The main instrument for measuring sound levels in the environment is the sound level meter. Most sound level meters provide readings in A, C, and Z-weighted decibels and must meet international standards such as IEC 61672-2013.

Examples

The lower limit of audibility is defined as SPL of , but the upper limit is not as clearly defined. While ( or ) is the largest pressure variation an undistorted sound wave can have in Earth's atmosphere (i.e. if the thermodynamic properties of the air are disregarded, in reality the sound waves become progressively non-linear starting over 150 dB), larger sound waves can be present in other atmospheres or other media, such as underwater or through the Earth.

Ears detect changes in sound pressure. Human hearing does not have a flat spectral sensitivity (frequency response) relative to frequency versus amplitude. Humans do not perceive low- and high-frequency sounds as well as they perceive sounds between 3,000 and 4,000 Hz, as shown in the equal-loudness contour. Because the frequency response of human hearing changes with amplitude, three weightings have been established for measuring sound pressure: A, B and C.

In order to distinguish the different sound measures, a suffix is used: A-weighted sound pressure level is written either as dB_A or L_A. B-weighted sound pressure level is written either as dB_B or L_B, and C-weighted sound pressure level is written either as dB_C or L_C. Unweighted sound pressure level is called "linear sound pressure level" and is often written as dB_L or just L. Some sound measuring instruments use the letter "Z" as an indication of linear SPL.

Distance

The distance of the measuring microphone from a sound source is often omitted when SPL measurements are quoted, making the data useless, due to the inherent effect of the inverse proportional law. In the case of ambient environmental measurements of "background" noise, distance need not be quoted, as no single source is present, but when measuring the noise level of a specific piece of equipment, the distance should always be stated. A distance of one metre (1 m) from the source is a frequently used standard distance. Because of the effects of reflected noise within a closed room, the use of an anechoic chamber allows sound to be comparable to measurements made in a free field environment.

According to the inverse proportional law, when sound level ''L''_''p''1 is measured at a distance ''r''₁, the sound level ''L''_''p''2 at the distance ''r''₂ is
$L_ = L_ + 20 \log_\left( \frac \right)~\text.$

Multiple sources

The formula for the sum of the sound pressure levels of ''n'' incoherent radiating sources is
L_\Sigma = 10 \log_\left(\frac\right)~\text =
10 \log_\left left(\frac\right)^2 + \left(\frac\right)^2 + \dots + \left(\frac\right)^2\right\text.

Inserting the formulas
$\left(\frac\right)^2 = 10^,\quad i = 1, 2, \ldots, n$
in the formula for the sum of the sound pressure levels yields
$L_\Sigma = 10 \log_ \left(10^ + 10^ + \dots + 10^ \right)~\text.$

Examples of sound pressure

See also

*Acoustics
*Phon (unit)
*Loudness
*Sone (unit)
* Sound level meter
*Stevens's power law
*Weber–Fechner law, especially The case of sound

References

;General
*Beranek, Leo L., ''Acoustics'' (1993), Acoustical Society of America, .
*Daniel R. Raichel, ''The Science and Applications of Acoustics'' (2006), Springer New York, .

External links

*
Sound Pressure and Sound Power, Effect and Cause
* ttp://www.sengpielaudio.com/TableOfSoundPressureLevels.htm Table of Sound Levels, Corresponding Sound Pressure and Sound Intensitybr>Ohm's Law as Acoustic Equivalent, CalculationsRelationships of Acoustic Quantities Associated with a Plane Progressive Acoustic Sound Wave
* ttp://www.sengpielaudio.com/calculator-levelchange.htm How Many Decibels Is Twice as Loud? Sound Level Change and the Respective Factor of Sound Pressure or Sound Intensitybr>Decibel (Loudness) Comparison Chart

{{Authority control

Acoustics
Sound
Sound measurements
Physical quantities
Acoustic equations